 |
Matronics Email Lists Web Forum Interface to the Matronics Email Lists
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in| Search found 9 matches |
| Author | Message |
|---|---|
 Topic: RV7-List Digest: 1 Msgs - 06/21/09 |
|
| frazitl Replies: 1 Views: 2100 |
 Forum: RV7-List Posted: Mon Jun 22, 2009 6:09 pm Subject: RV7-List Digest: 1 Msgs - 06/21/09 |
| You really should just wait until you mount the tail on the fuselage to
measure and set the max deflection angles. They are limited by small rudder stops attached to the lower fuselage. My advice ... |
|
| Topic: -List: Rod End Bearing Jam Nut - TORQUE |
|
| frazitl Replies: 0 Views: 1819 |
Forum: RV7-List Posted: Thu Jun 04, 2009 5:54 am Subject: -List: Rod End Bearing Jam Nut - TORQUE |
| On the lock nuts, I just tightened them as well as I could. Impossible to
get a torque wrench in there. Be sure to use torque seal or nail polish for future inspection purposes. On calibratin ... |
|
| Topic: Fuel Line Bends |
|
| frazitl Replies: 2 Views: 2759 |
Forum: RV7-List Posted: Mon Sep 15, 2008 7:00 am Subject: Fuel Line Bends |
| I have been able to get closer "S-bends" by bending from opposite sides
toward the center, if that makes sense. Make your first bend, then turn the tubing around and make the second bend ... |
|
| Topic: Setting the correct Spacing (Gap) between VS Top Rib and Rud |
|
| frazitl Replies: 0 Views: 1880 |
Forum: RV7-List Posted: Sat May 10, 2008 6:38 am Subject: Setting the correct Spacing (Gap) between VS Top Rib and Rud |
| I had no problems with the gap just constructing the vert. stab and rudder
according to the plans. The vertical height of the gap is set by the prepunched holes in the stab and rudder hinge /rod en ... |
|
| Topic: Comm Antenna |
|
| frazitl Replies: 8 Views: 8686 |
Forum: AeroElectric-List Posted: Mon May 05, 2008 8:14 am Subject: Comm Antenna |
| FWIW, I looked up the installation instructions on the artex ME406 ELT
http://www.artex.net/products/oneproduct.php?categoryid=15&productid=87 . They call for a shielded cable between the ELT an ... |
|
| Topic: Subject: Re: Re: Brownout Battery System P.S. |
|
| frazitl Replies: 0 Views: 1289 |
Forum: AeroElectric-List Posted: Wed Apr 23, 2008 7:19 am Subject: Subject: Re: Re: Brownout Battery System P.S. |
| I'm building a 7A with a somewhat modified z19 system. I'll probably use
both 16ah batteries to start, so I am concerned about EFIS (GRT) brownout too. I've been thinking for some time that the br ... |
|
| Topic: VOR Diplexer |
|
| frazitl Replies: 1 Views: 1875 |
Forum: AeroElectric-List Posted: Wed Mar 05, 2008 7:55 am Subject: VOR Diplexer |
| I'm building an RV7A with one SL-30 radio and inside the wingtip antennae.
I'll probably use the Sport Aircraft design for the antennae. Question is, can I use a diplexer "backwards" to f ... |
|
| Topic: [OT] boat wiring specificity |
|
| frazitl Replies: 3 Views: 3527 |
Forum: AeroElectric-List Posted: Wed Feb 27, 2008 10:09 am Subject: Re: [OT] boat wiring specificity |
| On 2-26 you wrote:
"I've been considering switching to RG batteries in my sailboat. Batteries are used for all power and the engine isn't run very often. There is a power charger used in harbo ... |
|
| Topic: Flap Switch Protection |
|
| frazitl Replies: 5 Views: 4210 |
Forum: AeroElectric-List Posted: Mon Feb 11, 2008 9:57 am Subject: Flap Switch Protection |
| I'm using Van's electric flap motor with a on-off-(mom)on dpdt switch. I'm
looking for a protection config. for the switch similar to that used on the battery/starter contactors. Found one diagram ... |
|
All times are GMT - 8 Hours |
Powered by phpBB © 2001, 2005 phpBB Group