Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Question on rudder cable bearing location?

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List
View previous topic :: View next topic  
Author Message
jeffrey-j-paris(at)excite
Guest
PostPosted: Sat Jun 21, 2008 3:28 am    Post subject: Question on rudder cable bearing location? Reply with quote
Dear Thread,

A quick question? I am in the process of running my rudder cables. I am at the part of the instructions in which we fabricated the 20mm x 30mm Tufnil blocks that are to be located on the plywood triangle seat support ribs. When we place ours on the rib the cable ends up rubbing on the inside walls of the console. If we make new and deeper blocks I'm concerned with clearance of the landing gear (monowheel). Does anybody have pictures or run into the same problem. I may have just place the triangle rib supports a tad bit outboard than I should have.

Thank you for your time and consideration.

Cheers,

Jeff Paris Kit # A012 Classic Monowheel

_______________________________________________
Join Excite! - http://www.excite.com
The most personalized portal on the Web!

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
hagargs(at)earthlink.net
Guest
PostPosted: Sat Jun 21, 2008 6:19 am    Post subject: Question on rudder cable bearing location? Reply with quote
Jeff:

Make some guides out of Nylaflo tubing to run the cables through, for the
sides of the wheel well cavity. It is available through Aircraft Spruce.

Steve Hagar
A143
Mesa, AZ
Quote:
[Original Message]
From: Jeffrey J Paris <jeffrey-j-paris(at)excite.com>
To: <europa-list(at)matronics.com>
Date: 6/21/2008 4:31:45 AM
Subject: Question on rudder cable bearing location?


<jeffrey-j-paris(at)excite.com>

Quote:

Dear Thread,

A quick question? I am in the process of running my rudder cables. I am
at the part of the instructions in which we fabricated the 20mm x 30mm

Tufnil blocks that are to be located on the plywood triangle seat support
ribs. When we place ours on the rib the cable ends up rubbing on the
inside walls of the console. If we make new and deeper blocks I'm
concerned with clearance of the landing gear (monowheel). Does anybody
have pictures or run into the same problem. I may have just place the
triangle rib supports a tad bit outboard than I should have.
Quote:

Thank you for your time and consideration.

Cheers,

Jeff Paris Kit # A012 Classic Monowheel

_______________________________________________
Join Excite! - http://www.excite.com
The most personalized portal on the Web!



- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
jeffrey-j-paris(at)excite
Guest
PostPosted: Sat Jun 21, 2008 10:46 am    Post subject: Question on rudder cable bearing location? Reply with quote
Thanks Steve excellent idea!

--- On Sat 06/21, Steve Hagar < hagargs(at)earthlink.net > wrote:
From: Steve Hagar [mailto: hagargs(at)earthlink.net]
To: europa-list(at)matronics.com
Date: Sat, 21 Jun 2008 07:15:11 -0700
Subject: RE: Question on rudder cable bearing location?



_______________________________________________
Join Excite! - http://www.excite.com
The most personalized portal on the Web!

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
ptag.dev(at)tiscali.co.uk
Guest
PostPosted: Sat Jun 21, 2008 11:09 am    Post subject: Question on rudder cable bearing location? Reply with quote
Hi! Jeffrey
Yes, the suggestions others have made about running your cables through
tubing is good but don't despair if you later find you need another run
slightly diverting. As an afterthought without removing the cable to put
another length of tubing in place then use some spiral wrap electrical
conduit by winding it into pace. A dab of redux here and there fixes it.
Regards
Bob Harrison. G-PTAG

--

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
rlborger(at)mac.com
Guest
PostPosted: Sat Jun 21, 2008 11:18 am    Post subject: Question on rudder cable bearing location? Reply with quote
Jeff,

Check my build web site (URL in signature block). Go to album Year
#3, Q1 2004. Down toward the bottom is a pic taken down the tunnel,
looking aft, of the rudder cables, pulleys and the safety blocks. You
can see the rudder cables coming out of the nylon, Nyloflow tubing.
If this isn't what you want, let me know and I'll try to find a pic
with the information you need.

Good building and great flying,
Bob Borger
Europa Kit #A221 N914XL, XS Mono, Intercooled 914, Airmaster C/S
http://www.europaowners.org/N914XL
(95% done, only 95% to go) tail kit done, wings closed, cockpit module
installed, pitch system in, landing gear complete, rudder system in
with Singleton Mod, outrigger mod in, Fuselage Top on, lift/drag/flap
pins in, wing incidence set, tie bar in, flap drive in, baggage bay
in. Fuel system complete. Rotax and Airmaster installed. Mods 62,
66, 70 & 72 done. Completed the instrument panel install. Europa
interior kit being installed. Installed windows. Working in - 25
Electrical, 28 Flaps, 30 Fuel System, 32 Tail, 34 Door Latches & 35
Doors, 37 Finishing. Mostly finishing these days.
3705 Lynchburg Dr.
Corinth, TX 76208
Home: 940-497-2123
Cel: 817-992-1117
On Jun 21, 2008, at 6:24, Jeffrey J Paris wrote:

Quote:

>

Dear Thread,

A quick question? I am in the process of running my rudder cables.
I am at the part of the instructions in which we fabricated the 20mm
x 30mm Tufnil blocks that are to be located on the plywood triangle
seat support ribs. When we place ours on the rib the cable ends up
rubbing on the inside walls of the console. If we make new and
deeper blocks I'm concerned with clearance of the landing gear
(monowheel). Does anybody have pictures or run into the same
problem. I may have just place the triangle rib supports a tad bit
outboard than I should have.

Thank you for your time and consideration.

Cheers,

Jeff Paris Kit # A012 Classic Monowheel

_______________________________________________
Join Excite! - http://www.excite.com
The most personalized portal on the Web!


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
jeffrey-j-paris(at)excite
Guest
PostPosted: Sun Jun 22, 2008 5:14 am    Post subject: Question on rudder cable bearing location? Reply with quote
Thanks Bob!

--- On Sat 06/21, Robert Borger < rlborger(at)mac.com > wrote:
From: Robert Borger [mailto: rlborger(at)mac.com]
To: europa-list(at)matronics.com
Date: Sat, 21 Jun 2008 14:15:30 -0500
Subject: Re: Question on rudder cable bearing location?


Airmaster installed. Mods 62, <br>66, 70 & 72 done. Completed the instrument panel install. Europa <br>interior kit being installed. Installed windows. Working in - 25 <br>Electrical, 28 Flaps, 30 Fuel System, 32 Tail, 34 Door Latches & 35 <br>Doors, 37 Finishing. Mostly finishing these days.<br>3705 Lynchburg Dr.<br>Corinth, TX 76208<br>Home: 940-497-2123<br>Cel: 817-992-1117<br><br><br><br><br><br><br>On Jun 21, 2008, at 6:24, Jeffrey J Paris wrote:<br><br>>

_______________________________________________
Join Excite! - http://www.excite.com
The most personalized portal on the Web!

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group