 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Rowland_Carson
Joined: 04 Jul 2008
Posts: 155
Location: Cheltenham, England
|
 Posted: Thu Aug 14, 2008 12:49 pm Post subject: control bearing installation |
 |
|
I am nearly ready to install the SRBF (Tufnol) bearings for the main
roll torque tubes.
For the forward bearing CS04, the words on page 13-6 and the exploded
fastener diagram on page 13-12 do not show a washer between the bolt
head and the Tufnol. Only the large washer on the glass-fibre side of
the assembly is mentioned. But the assembled bolt shown in the other
hole of CS04 does appear to have a washer under its head.
However, the words on page 13-6 and the diagram on page 13-13 for the
aft bearing CS06 both show AN960-10L washers between the nuts and the
Tufnol.
Fitting the washers on the forward bearing fasteners would make the
installation consistent with that for the aft bearings. Does anyone
think I'd be wrong to fit the AN960-10L washers under the front
bearing bolt heads, or is there a good reason for them to be omitted?
BTW, my inventory shows that if I don't fit them, I actually have 4
washers surplus in the fuselage kit; if I do fit them I am 4 short!
regards
Rowland
--
| Rowland Carson LAA #16532 http://home.clara.net/rowil/aviation/
| 1070 hours building Europa #435 G-ROWI e-mail <rowil(at)clara.net>
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
 |
aireupora(at)sbcglobal.ne
Guest
|
| Posted: Thu Aug 14, 2008 5:12 pm Post subject: control bearing installation |
|
|
Rowland, for what it is worth. I followed the manual and did not install the washers AN960-10L under the bolt on the front Tufnol bearing. I did install them on the back Tufnol bearing. Take a look at page 13-12 and page 13-13 issue 3.
Rick Stockton
A210
Rowland Carson <rowil(at)clara.net> wrote:
[quote]--> Europa-List message posted by: Rowland Carson
I am nearly ready to install the SRBF (Tufnol) bearings for the main
roll torque tubes.
For the forward bearing CS04, the words on page 13-6 and the exploded
fastener diagram on page 13-12 do not show a washer between the bolt
head and the Tufnol. Only the large washer on the glass-fibre side of
the assembly is mentioned. But the assembled bolt shown in the other
hole [quote][b]
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
