Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

io360-a1b

Matronics Email Lists Forum Index -> RV-List

View previous topic :: View next topic

Author Message

gert.v(at)sbcglobal.net
Guest

Posted: Thu Aug 10, 2006 7:27 pm Post subject: io360-a1b

Hi Folks



can anybody tell me the difference between the 06A19956 and STD2217 oil 

seals, both are 7/8" i.d. x 1-1/2" o.d. x 5/16" wide.

according to the parts book, my vacuum pump adapter should have the 

06A19956 seal, but has the STD2217 seal and it needs replacing,

also, in the parts book, page 2-4 of the parts manual, it shows steel 

ring #3 to sit on top of the drive gear, under the tail of #16. However 

on page 5-4 of the overhaul manual as well as on page 1-23 of the limits 

and torque supplement, it shows the steel ring under the snapring 

holding the shaft in place. I looked at two adapters, and wouldn't u 

know, one had the ring on top and one had the ring at the bottom. 

Anybody knows the correct placement??



any input greatly appreciated.

Thanks

Gert



-- 



-------------------------------------------------------------------

Pursuant to US Code, Title 47, Chapter 5, Subchapter II, '227,

any and all nonsolicited commercial E-mail sent to this address

is subject to a download and archival fee in the amount of $500

US.  E-mailing denotes acceptance of these terms.



--------------------------------------------------------------------

- The Matronics RV-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV-List

Rhonda(at)bpaengines.com
Guest

Posted: Fri Aug 11, 2006 5:20 am Post subject: io360-a1b

The 06A19956 part number is the superceding p/n for STD-2217 according

to the Lycoming Parts History manual.  Probably no difference other than

who the vendor is that was used to produce the part number, or a process

change in how the seal was manufactured.



Rhonda

--

- The Matronics RV-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV-List

gert.v(at)sbcglobal.net
Guest

Posted: Sat Aug 12, 2006 10:43 am Post subject: io360-a1b

Thanks Rhonda



any resolution on the correct position of the steel ring in the governor 

drive adapter??



Gert



Rhonda Bewley wrote:

[quote] 



 The 06A19956 part number is the superceding p/n for STD-2217 according

 to the Lycoming Parts History manual.  Probably no difference other than

 who the vendor is that was used to produce the part number, or a process

 change in how the seal was manufactured.



 Rhonda

 --

- The Matronics RV-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV-List

BPA(at)bpaengines.com
Guest

Posted: Tue Aug 15, 2006 7:23 am Post subject: io360-a1b

The governor drive shaft has a thrust surface, therefore the 'steel

ring' which is actually a thrust washer installs between the housing and

retaining ring. The picture in some of the parts catalogs that show the

ring directly under the gear end of the drive shaft is a typo.



Allen Barrett

BPE, Inc.



--

- The Matronics RV-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV-List

Display posts from previous:

	Matronics Email Lists Forum Index -> RV-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum