Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

601XL Flaps

Matronics Email Lists Forum Index -> Zenith-List

View previous topic :: View next topic

Author Message

GLJSOJ1

Joined: 18 Aug 2007
Posts: 82
Location: Chesapeake, Virginia

Posted: Thu Nov 15, 2007 8:32 am Post subject: 601XL Flaps

HI CHET

  

 MY SRAWING ON PAGE 6-W-1, SRAWING NO 1 SHOWS A MEASURMENT OF 40MM DOWN AND 80MM BACK FROM THE TOP CORNER (ONLY 90 DEG CORNER) OF THE FLAP RIB.  THE DRAWING JUST BELOW IT SAYS TO MOUNT THE NYLONPLATE AT A 90 DEG ANGLE TO THE BOTTOM ON THE RIB.  HOPE THIS HELPS

  

 GLENN

 601XL CHESAPEAKE VA  ALMOST DONE



  	  Quote: 	
		    From: CHETKRU(at)aol.com

Date: Thu, 15 Nov 2007 10:34:10 -0500

Subject: 601XL Flaps

To: zenith-list-digest(at)matronics.com



  Hi Folks, I am installing my flaps and would like some info on how to connect the flap to the actuator arm. I am having trouble getting measurements to drill the hole in the nylon control plate. Thanks.

  

 Chet Kruleski

 Las Vegas, NV



   See wha  	  Quote: 	
		  



blank>http://www.matronics.com/contribution

arget=_blank>http://www.matronics.com/Navigator?Zenith-List

p://forums.matronics.com



	


	
Help yourself to FREE treats served up daily at the Messenger Café. Stop by today!  [quote][b]

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

_________________
601XL N676L FLYING PHASE I
CHESAPEAKE VA

amyvega2005(at)earthlink.
Guest

Posted: Thu Nov 15, 2007 5:09 pm Post subject: 601XL Flaps

what nylon control plate?



Juan



--

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

amyvega2005(at)earthlink.
Guest

Posted: Thu Nov 15, 2007 5:16 pm Post subject: 601XL Flaps

now i get the nylon plate, took a senior monent.  install the flaps at very last.  use the measurements provided in the plans on the arm throws for servos. 65 to 185 mm. next follow plans for drilling location for nylon plate.  do not drill arm to flap rod yet. just slide the flaps and cleco in place at neutral zero flap position. make sure to install the flap nylon stops. once flaps are set at zero setting  go under the plane and mark where the arm hits the two flap pipes.  scrib it then take back to shop and drill. after drilling, cleco flap back on and put the arm and pipes all together and screw.  then check the throws on flaps by turning on the motor and adjusting the servos to suite the throws you want.  when all is working according to plan, then rive the flaps as the lasty thing.



Juan



--

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

JAPhillipsGA(at)aol.com
Guest

Posted: Thu Nov 15, 2007 5:20 pm Post subject: 601XL Flaps

Juan, you know the slab of white nylon plate located on the end of the flap that didn't fit the measurements from Zac's plans, that we had to move about five times before we found out were they should really be located. That nylon plate. Remember? Best regards, Bill of Georgia

**************************************

  [quote][b]

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum