 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Mike Whisky
Joined: 05 Jun 2006
Posts: 336
Location: Switzerland
|
 Posted: Sat May 17, 2008 10:38 am Post subject: Ignition Cable clamp |
 |
|
Who knows where I can get two of these ignition cable clamps (for three cables)!
Michael
Zuerich, Switzerland
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
| Description: |
|
| Filesize: |
103 KB |
| Viewed: |
307 Time(s) |
|
_________________
RV-10 builder (flying)
#511 |
|
| Back to top |
|
 |
pitts_pilot(at)bellsouth.
Guest
|
| Posted: Sat May 17, 2008 11:01 am Post subject: Ignition Cable clamp |
|
|
I don't know a source, but you can take a plain ADEL clamp (a 1 1/4"
should do it) and remove the rubber part. Put a screw through the hole
and tighten up a nut. Place a 3/8" thick piece of 'something' in the
clamp and squeeze in a vise to make the clamp oblong. Replace the
rubber part and you should have a usable clamp.
Linn
Michael Wellenzohn wrote:
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
Albert Gardner
Joined: 10 Jan 2006
Posts: 455
Location: Yuma, AZ
|
| Posted: Sat May 17, 2008 11:55 am Post subject: Ignition Cable clamp |
|
|
Are you thinking of the Engine Baffle Ignition Wire Seals like on aircraft
Spruce cat/ page 272? Or something else?
Albert Gardner
Yuma, AZ
--
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________
RV-9A N872RV
RV-10 N991RV |
|
| Back to top |
|
|
pitts_pilot(at)bellsouth.
Guest
|
| Posted: Sat May 17, 2008 5:52 pm Post subject: Ignition Cable clamp |
|
|
Duh!!! Good question!!!! If he is looking for the baffle feed-through
clamps ..... makes my suggestion seem pretty stupid!!!
But then again, if someone is looking for ignition clamps that attach to
the valve covers ..... Bingo!!!
Linn
do not archive!!
Albert Gardner wrote:
[quote]
Are you thinking of the Engine Baffle Ignition Wire Seals like on aircraft
Spruce cat/ page 272? Or something else?
Albert Gardner
Yuma, AZ
--
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
Mike Whisky
Joined: 05 Jun 2006
Posts: 336
Location: Switzerland
|
| Posted: Sun May 18, 2008 1:37 am Post subject: Re: Ignition Cable clamp |
|
|
Linn,
I I am looking for the ignition clamps that attach to
the valve covers as you said the Adel Clamp modification is one way. However I wonder if there are the clamps for one and for two cables there must be also some out there for three did all six cylinder engine owners manufacture them themselves?
Michael
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________
RV-10 builder (flying)
#511 |
|
| Back to top |
|
|
pitts_pilot(at)bellsouth.
Guest
|
| Posted: Sun May 18, 2008 5:37 am Post subject: Ignition Cable clamp |
|
|
Michael Wellenzohn wrote:
| Quote: |
Linn,
I I am looking for the ignition clamps that attach to
the valve covers as you said the Adel Clamp modification is one way. However I wonder if there are the clamps for one and for two cables there must be also some out there for three did all six cylinder engine owners manufacture them themselves?
Another good question!!!! Most all engines come with an ignition
|
harness and those clamps, and I've seen clamps that were pretty ragged
..... even missing the plastic and they put electricians tape on the
wires for anti-chafe!!! If you really want the 'real' clamps, then I'd
start looking at the magneto manufacturers themselves. I have a
downloaded Aircraft Spruce catalog on my workshop computer, but can't
get it to download on this one. The clamps may be available thru Spruce
...send them an email. I suspect that with a long ..... really long
... distance phone call and shipping it may be easier for you to make
your own.
Linn
do not archive
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
