 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
rparigor(at)suffolk.lib.n
Guest
|
 Posted: Fri Apr 17, 2009 10:53 am Post subject: Scuff sanding before top fuse goes on and other ideas |
 |
|
Prior to bonding on top fuse, besides what is mentioned in manual to scuff sand, figure we will scuff sand fin rib contact area and area that will get 2 BID, sternpost and sternpost contact area, baggage bulkhead and baggage bulkhead contact area and area that gets 2 BID, door sill area that will get 2 BID and balsa for strengthening / wire conduit.
Not going to make a splash for mass balance tower or fin rib.
*Rudder cables, turnbuckles and guides installed.
*All antennas installed, wired and tested (except transponder).
*Pitch servo wired.
*Fuel system installed (914) and pumps wired.
*Tailwheel pad installed (mono) and steel outrigger to help support twisting forces on mounting bolt.
*Fin rib has foam dug out for better bite upon bonding (then will get 2 BID from rear).
*Aft Odyssey PC545 battery mount installed with CCA wire strain relief supports on top clamp.
*Any ty wrap clips needed aft of baggage bulkhead installed.
*Any gaps larger than in lower fuse between bottom of joggle and where foam begins is filled with PVC foam and 2 BID over)
*406Mhz ELT installed
*Mono undercarriage installed
*Airbrake lever and control horn installed.
*Ceiling installed and aft portion wired.
*Rollbar installed with attachments for shoulder harness x2.
*Filler cap receptical installed and area that cobra attaches has balsa and BID reinforcement.
*Fuel tank has BID reinforcement in tunnel and bottom is filled with foam to help support.
*Baggage ribs installed to fuse with splash on the tops.
*Two cameras, one in fin and one on aft ceiling mounted and wired. DVR mounted on folding tray attached to baggage bulkhead to allow aft access.
* Will make holes to run pneumatic and wires to wings going down side of fuse prior to top bond on.
Will rig wings with top permanent bonded on to remove any change that may occur, will take hit having to rig flaps and rear lift pin crossbar with top on.
What did I miss?
Any negative comments?
Thx.
Ron Parigoris
Visit - www.EuropaOwners.org
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
 |
raimo.toivio(at)rwm.fi
Guest
|
| Posted: Tue Apr 21, 2009 3:26 am Post subject: Scuff sanding before top fuse goes on and other ideas |
|
|
Ron,
Wau,
| Quote: | *Two cameras, one in fin and one on aft ceiling mounted and wired. DVR mounted on folding tray attached to baggage bulkhead to allow aft access
|
would you like to give some more information of your cameras?!!!
Raimo OH-XRT
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
