Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Main gear structural question

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> L29-List
View previous topic :: View next topic  
Author Message
paulhath(at)comcast.net
Guest





PostPosted: Wed Mar 16, 2011 12:04 pm    Post subject: Main gear structural question Reply with quote

Hi all,

OK, extra credit for anyone who knows the answer to this one!

I've removed the main gear as part of the total rebuild of my 29.

In each main gear well, just aft and inboard of each main gear swing bearing there there is a long structural piece. It is held in place by three bolts on one end and by a bearing bushing on the other.

The inboard bearing for the main gear "folding strut" PN L 29.501-11 goes through this piece.

I can't find the schematic for this 'structural piece' anywhere in the parts catalog 1 & 2.

I've removed the bolts on the inboard end. I've also removed the through bolt in the bellcrank that connects the main gear hydraulic actuator to the folding strut.

How do you remove the outboard end of this assembly? The bushing looks like it is internally threaded for a pulling tool. I can't seem to see any clips on the back side of the part that retain it.

This is the last thing I need to remove before stripping and repainting, so help is appreciated.

I have photos if anyone needs clarification.

Best regards

Paul
[quote][b]


- The Matronics L29-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?L29-List
Back to top
paulhath(at)comcast.net
Guest





PostPosted: Wed Mar 16, 2011 12:25 pm    Post subject: Main gear structural question Reply with quote

Here are pictures of the assembly. Hopefull these will get through.

Cheers

Paul

[img]cid:48C2CA023B8849E28F9B08907F6842DD(at)MainPC[/img]


[img]cid:0EDAA2FE397E477EBBB34888B05B60A6(at)MainPC[/img]
[quote] ---


- The Matronics L29-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?L29-List



L-29_March_2011_113.JPG
 Description:
 Filesize:  71.45 KB
 Viewed:  1412 Time(s)

L-29_March_2011_113.JPG



L-29_March_2011_111.JPG
 Description:
 Filesize:  120.95 KB
 Viewed:  1412 Time(s)

L-29_March_2011_111.JPG


Back to top
SD737(at)aol.com
Guest





PostPosted: Wed Mar 16, 2011 6:56 pm    Post subject: Main gear structural question Reply with quote

If you or anyone else need a new set of L-29 Landing Gear get a hold of me directly via my email.
I have a set of main L-29 landing gear.
The main gear is something that gets used every time and cycles of their usage could become an issue with the FAA. Always good to have a spare set!
Scott
SD737(at)AOL.COM

In a message dated 3/16/2011 1:04:41 P.M. Pacific Daylight Time, paulhath(at)comcast.net writes:
Quote:
Hi all,

OK, extra credit for anyone who knows the answer to this one!

I've removed the main gear as part of the total rebuild of my 29.

In each main gear well, just aft and inboard of each main gear swing bearing there there is a long structural piece. It is held in place by three bolts on one end and by a bearing bushing on the other.

The inboard bearing for the main gear "folding strut" PN L 29.501-11 goes through this piece.

I can't find the schematic for this 'structural piece' anywhere in the parts catalog 1 & 2.

I've removed the bolts on the inboard end. I've also removed the through bolt in the bellcrank that connects the main gear hydraulic actuator to the folding strut.

How do you remove the outboard end of this assembly? The bushing looks like it is internally threaded for a pulling tool. I can't seem to see any clips on the back side of the part that retain it.

This is the last thing I need to remove before stripping and repainting, so help is appreciated.

I have photos if anyone needs clarification.

Best regards

Paul
Quote:


====================================
="http://www.matronics.com/Navigator?L29-List">http://www.matronics.com/Navigator?L29-List
====================================
ms.matronics.com/">http://forums.matronics.com
====================================
tp://www.matronics.com/contribution">http://www.matronics.com/contribution
====================================


[quote][b]


- The Matronics L29-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?L29-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> L29-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group