Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

CH601HD flaps

Matronics Email Lists Forum Index -> Zenith601-List

View previous topic :: View next topic

Author Message

mvarelasartal(at)yahoo.es
Guest

Posted: Thu Nov 15, 2012 12:20 pm Post subject: CH601HD flaps

Hi to everybody,

I´m building a CH601HD and I´m interested on install flaps due to the airfield that we fly (big trees on main header).

I looking around on the net for information about this and found some kind of split flaps installed on the European Version of the CH601, mainly in the UK. I saw some pictures from this planes but that´s all, Is there any way to found this sheets or plans? Any imput or suggestion would be apreciated....

Best regards

Marcos Varela

SPAIN



 [quote][b]

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

jerryvmd

Joined: 18 Apr 2008
Posts: 25

Posted: Thu Nov 15, 2012 1:18 pm Post subject: CH601HD flaps

Marcos,

       I have about 350 hours on my 601HD.  Believe me, you DO NOT need       flaps on a HD.  If I am high on final, all I need to do is pull       power to idle and the HD will settle like an elevator.  Worse case       is a side slip but that is rarely necessary.

       Jerry

       On 11/15/2012 3:19 PM, Marcos Varela Sartal wrote:

     

     [quote]                Hi to everybody,

         I´m building a CH601HD and I´m interested on install flaps           due to the airfield that we fly (big trees on main header).

         I looking around on the net for information about this and           found some kind of split flaps installed on the European           Version of the CH601, mainly in the UK. I saw some pictures           from this planes but that´s all, Is there any way to found           this sheets or plans? Any imput or suggestion would be           apreciated....

         Best regards

         

         

         Marcos Varela

         SPAIN

       

        	  Quote: 	
		  

	
     [b]

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

dgraham7(at)TWCNY.RR.COM
Guest

Posted: Thu Nov 15, 2012 2:07 pm Post subject: CH601HD flaps

I have the 601 HDS and that does not need flaps either. Just pull the power and it comes right down.

Regards,

Damien



Sent from my iPad



On Nov 15, 2012, at 4:18 PM, "GERALD A. APPLEFELD" <jerryvmd(at)embarqmail.com (jerryvmd(at)embarqmail.com)> wrote:

[quote]                   Marcos,

       I have about 350 hours on my 601HD.  Believe me, you DO NOT need       flaps on a HD.  If I am high on final, all I need to do is pull       power to idle and the HD will settle like an elevator.  Worse case       is a side slip but that is rarely necessary.

       Jerry

       On 11/15/2012 3:19 PM, Marcos Varela Sartal wrote:

     

      	  Quote: 	
		                  Hi to everybody,

         IÂ´m building a CH601HD and IÂ´m interested on install flaps           due to the airfield that we fly (big trees on main header).

         I looking around on the net for information about this and           found some kind of split flaps installed on the European           Version of the CH601, mainly in the UK. I saw some pictures           from this planes but thatÂ´s all, Is there any way to found           this sheets or plans? Any imput or suggestion would be           apreciated....

         Best regards

         

         

         Marcos Varela

         SPAIN

       

        	  Quote: 	
		  

	
     



===================================

ctric.com

 	  Quote: 	
		  www.buildersbooks.com

uilthelp.com
	


matronics.com/contribution

===================================

 	  Quote: 	
		  http://www.matronics.com/Navigator?Zenith601-List

===================================
	


cs.com

===================================



	


[b]

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

mvarelasartal(at)yahoo.es
Guest

Posted: Thu Nov 15, 2012 2:42 pm Post subject: CH601HD flaps

Hello Jerry, thanks a lot for your info. I´m a begginner with only about 50 hours of flight.

I flew about 40 hours on a Tecnam P92 to get my Permit to Fly and about 15 hours on my homebuilt Minimax. I have no problems with my Minimax as it land at about 40km/h and like you said, just cutt off engine to iddle and down...But with P92 you need to approach very high to avoid the trees (there are always turbulences up there) and after, you eat a lot of the runway even with flaps. I compared it because the approach speed is similar to CH601HD. Another reason is the nose up attitude that let the flaps. I flew 4 hours for practice on a Zephyr 2000 (faster airplane) and you need almost the entire track......

I have an Jabiru 2200 engine for it, that´s the reason I choose the 601HD instead of the XL.

Just some more questions, I  read a lot on the net about this airplane but:

-What´s the real cruise speed?

- Is true that in flight normally takes a nose high attitude?

- Is true that baggage compartments covers on wings move in flight?

Thanks a lot for your comments and sorry for my poor english..

My Best Regards

Marcos



P.D. Here it´s a link to my Minimax in flight http://www.youtube.com/watch?v=SzrQn_37P0g





        De: GERALD A. APPLEFELD <jerryvmd(at)embarqmail.com>

 Para: zenith601-list(at)matronics.com 

 Enviado: Jueves 15 de noviembre de 2012  22:18

 Asunto: Re: Zenith601-List: CH601HD flaps

  

 

                    Marcos,

       I have about 350 hours on my 601HD.  Believe me, you DO NOT need       flaps on a HD.  If I am high on final, all I need to do is pull       power to idle and the HD will settle like an elevator.  Worse case       is a side slip but that is rarely necessary.

       Jerry

       On 11/15/2012 3:19 PM, Marcos Varela Sartal wrote:

     

      	  Quote: 	
		                  Hi to everybody,

         I´m building a CH601HD and I´m interested on install flaps           due to the airfield that we fly (big trees on main header).

         I looking around on the net for information about this and           found some kind of split flaps installed on the European           Version of the CH601, mainly in the UK. I saw some pictures           from this planes but that´s all, Is there any way to found           this sheets or plans? Any imput or suggestion would be           apreciated....

         Best regards

         

         

         Marcos Varela

         SPAIN

       

        	  Quote: 	
		  



	
     http://www.matronics.com/contributionttp://www.matronics.com/Navigator?Zenith601-List">http://www.matronics.com/========================

" target="_blank" href="http://forums.matronics.com/">http://forums.mat===================


	




 

 

  

 [quote][b]

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

jerryvmd

Joined: 18 Apr 2008
Posts: 25

Posted: Thu Nov 15, 2012 5:30 pm Post subject: CH601HD flaps

Marcos,

       I have a Jabiru 3300, no wheel pants and built per plans except I       added the forward tilt canopy.  If you stiffen the baggage locker       doors (check the list archives) and add extra Dzus fasteners (I       have a total of  then there is no movement in flight.  With the       3300 there is definitely no nose high attitude.  Most people are       finding the need for slight nose up trim or slight adjustment of       the horizontal stab.  but it is a weight and balance issue only.        Move the battery fore or aft to get the W&B in the center then       no problem.  I have leading edge fuel tanks with 15 gallons in       each plus an 8 gallon header tank.  With a fixed pitch Sensenich       prop I fly at an indicated of 105-110 mph at 2700 to 2750 RPM, at       a fuel burn of about 5.5 gal/hr.  If I increase RPM to 2800 I get       about 115 MPH but fuel burn goes up to 6 - 6.5 gal/hr.. At 2650       the fuel burn goes below 5 gal/hr and the cruise is about       99-100mph.  I still say no flaps needed for the HD.  If I pull       power and set for 60-65 indicated I can land in less than 700 feet       with little braking.  The descent angle is quite steep. I normally       do final at 70-75 and slow to 65 over the fence and still land in       less than 1000 feet.  Good luck it's a fine plane.

       Jerry 

       

       On 11/15/2012 5:42 PM, Marcos Varela Sartal wrote:

     

     [quote]       Hello Jerry,         thanks a lot for your info. I´m a begginner with only about 50         hours of flight.

         I flew about 40 hours on a Tecnam P92 to get my Permit to Fly         and about 15 hours on my homebuilt Minimax. I have no problems         with my Minimax as it land at about 40km/h and like you said,         just cutt off engine to iddle and down...But with P92 you need         to approach very high to avoid the trees (there are always         turbulences up there) and after, you eat a lot of the runway         even with flaps. I compared it because the approach speed is         similar to CH601HD. Another reason is the nose up attitude that         let the flaps. I flew 4 hours for practice on a Zephyr 2000         (faster airplane) and you need almost the entire track......

         I have an Jabiru 2200 engine for it, that´s the reason I choose         the 601HD instead of the XL.

         Just some more questions, I read a lot on the net about this         airplane but:

         -What´s the real cruise speed?

         - Is true that in flight normally takes a nose high attitude?

         - Is true that baggage compartments covers on wings move in         flight?

         Thanks a lot for your comments and sorry for my poor english..

         My Best Regards

         Marcos

       

     [b]

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

jeffrey_davidson(at)earth
Guest

Posted: Thu Nov 15, 2012 7:31 pm Post subject: CH601HD flaps

Marcos,

Let me second (or third) everything Jerry said.  He is exactly right.  No flaps needed.  RPMS and speeds match mine.  I have almost the same set up: 601 HD with the XL front hinged canopy and a Jabiru 3300.  Take off and landing videos are online.  Just Google "N601T".

Jeff Davidson



do not archive

--

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

mvarelasartal(at)yahoo.es
Guest

Posted: Fri Nov 16, 2012 12:22 pm Post subject: CH601HD flaps

Many thanks to all of you for your help.

I´m clear now, NO FLAPS..... Right now I fisnished the vertical tail and elevator, all the ribs done and planning to begin with the spars.

It sounds great the speeds you mentioned and enought for me and what I use to fly.

Thanks again



Marcos Varela

Spain 





        De: Gerald A. Applefeld VMD <jerryvmd(at)embarqmail.com>

 Para: zenith601-list(at)matronics.com 

 Enviado: Viernes 16 de noviembre de 2012 2:30

 Asunto: Re: CH601HD flaps

  

 

                    Marcos,

       I have a Jabiru 3300, no wheel pants and built per plans except I       added the forward tilt canopy.  If you stiffen the baggage locker       doors (check the list archives) and add extra Dzus fasteners (I       have a total of  then there is no movement in flight.  With the       3300 there is definitely no nose high attitude.  Most people are       finding the need for slight nose up trim or slight adjustment of       the horizontal stab.  but it is a weight and balance issue only.        Move the battery fore or aft to get the W&B in the center then       no problem.  I have leading edge fuel tanks with 15 gallons in       each plus an 8 gallon header tank.  With a fixed pitch Sensenich       prop I fly at an indicated of 105-110 mph at 2700 to 2750 RPM, at       a fuel burn of about 5.5 gal/hr.  If I increase RPM to 2800 I get       about 115 MPH but fuel burn goes up to 6 - 6.5 gal/hr.. At 2650       the fuel burn goes below 5 gal/hr and the cruise is about       99-100mph.  I still say no flaps needed for the HD.  If I pull       power and set for 60-65 indicated I can land in less than 700 feet       with little braking.  The descent angle is quite steep. I normally       do final at 70-75 and slow to 65 over the fence and still land in       less than 1000 feet.  Good luck it's a fine plane.

       Jerry 

       

       On 11/15/2012 5:42 PM, Marcos Varela Sartal wrote:

     

      	  Quote: 	
		         Hello Jerry,         thanks a lot for your info. I´m a begginner with only about 50         hours of flight.

         I flew about 40 hours on a Tecnam P92 to get my Permit to Fly         and about 15 hours on my homebuilt Minimax. I have no problems         with my Minimax as it land at about 40km/h and like you said,         just cutt off engine to iddle and down...But with P92 you need         to approach very high to avoid the trees (there are always         turbulences up there) and after, you eat a lot of the runway         even with flaps. I compared it because the approach speed is         similar to CH601HD. Another reason is the nose up attitude that         let the flaps. I flew 4 hours for practice on a Zephyr 2000         (faster airplane) and you need almost the entire track......

         I have an Jabiru 2200 engine for it, that´s the reason I choose         the 601HD instead of the XL.

         Just some more questions, I read a lot on the net about this         airplane but:

         -What´s the real cruise speed?

         - Is true that in flight normally takes a nose high attitude?

         - Is true that baggage compartments covers on wings move in         flight?

         Thanks a lot for your comments and sorry for my poor english..

         My Best Regards

         Marcos

       

     lder's Bookstore [url=http://www.b rel=]www.matronics.com/contribution">http://www.matronics.com/contribution[/url]tp://www.matronics.com/Navigator?Zenith601-List">http://www.matronics.com/N========================

" target="_blank" href="http://forums.matronics.com/">http://forums.mat===================

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

IMG_0388.jpg

Description:

Filesize:

92.2 KB

Viewed:

8144 Time(s)

11112012042.jpg

Description:

Filesize:

1.17 MB

Viewed:

8144 Time(s)

IMG_0444.jpg

Description:

Filesize:

170.18 KB

Viewed:

8144 Time(s)

IMG_0390.jpg

Description:

Filesize:

104.87 KB

Viewed:

8144 Time(s)

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith601-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum