Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Tailcone question

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV10-List
View previous topic :: View next topic  
Author Message
MChase(at)gdatp.com
Guest
PostPosted: Mon Mar 12, 2007 6:34 am    Post subject: Tailcone question Reply with quote
OK so here I am back with questions about the tail cone and that darn F-1032 Longerion? Anyway I think I am past the point of breaking them, but how about alignment with the skin. I see in the instructions that they want me us to line up the edges, did anyone else have an issue or have to work at this? Looking at a bunch of websites I don't see anyone who even talks about this effort. I am trying to figure out if I messed up my bend or if it is just because it was so cold in my shop when I tried to line everything up. I question more then the bend just because my alignment issues were not just limited to near the bend, but also existing forward of the bend with good alignment the first 1-2 feet then 1 foot off then back on just before the bend ect. This may be just the cold contributing to my issues as it was -28F that AM, I am definitely in the market for a small wood stove before next winter:-)

thanks for the help



Michael Chase
General Dynamics Armament and Technical Products
802-657-6029 Office
802-922-5930 Cell
mchase(at)gdatp.com


This e-mail message (including attachments, if any) is for the sole use of the intended recipient(s) and may contain information that is private, confidential, or exempt from disclosure. Any unauthorized review, use, copying, printing, disclosure, retention, or distribution is strictly prohibited. If you are not the intended recipient, please contact the sender by reply to this e-mail, and delete all copies without disclosing this message to others. Thank you.
[quote][b]

- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
GRANSCOTT(at)aol.com
Guest
PostPosted: Mon Mar 12, 2007 6:47 am    Post subject: Tailcone question Reply with quote
In a message dated 3/12/2007 10:36:28 AM Eastern Daylight Time, MChase(at)gdatp.com writes:
Quote:
I am definitely in the market for a small wood stove before next winter:-)


Michael...my friend is using a "waste" oil heater and getting his oil from the local FBO...it's working well for him and legal in this area...no wood to buy, only oil to haul, his shop heater is using about 3 gallons per hour and it's toasty warm! FYI

Patrick

ps he has a set up that filters the oil by a gravity feed through a filter then on to a second holding barrel, pretty good system. With the oil from the FBO he know's what he's getting, no antifreeze etc just good aviation oil...and the FBO was happy to give it to a local guy rather than the service company.

do not archive

AOL now offers free email to everyone. Find out more about what's free from AOL at AOL.com.
[quote][b]

- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
jjessen



Joined: 22 Apr 2006
Posts: 285
Location: OR
PostPosted: Mon Mar 12, 2007 6:54 am    Post subject: Tailcone question Reply with quote
Michael, some pictures would help.

If you looked at my website, and my discussion of the process, I didn't have alignment problems, but only because I snuck up on the final bend. You also have to be a little careful not to put a twist into it, so when you whack it, you really want the pressure you're putting on it to be in the final bend direction. Anyway, send some pictures of what the alignment problem is. And get some heat!

John Jessen
#40328

From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Michael D Chase
Sent: Monday, March 12, 2007 7:33 AM
To: rv10-list(at)matronics.com
Subject: Tailcone question


OK so here I am back with questions about the tail cone and that darn F-1032 Longerion? Anyway I think I am past the point of breaking them, but how about alignment with the skin. I see in the instructions that they want me us to line up the edges, did anyone else have an issue or have to work at this? Looking at a bunch of websites I don't see anyone who even talks about this effort. I am trying to figure out if I messed up my bend or if it is just because it was so cold in my shop when I tried to line everything up. I question more then the bend just because my alignment issues were not just limited to near the bend, but also existing forward of the bend with good alignment the first 1-2 feet then 1 foot off then back on just before the bend ect. This may be just the cold contributing to my issues as it was -28F that AM, I am definitely in the market for a small wood stove before next winter:-)

thanks for the help

Michael Chase
General Dynamics Armament and Technical Products
802-657-6029 Office
802-922-5930 Cell
mchase(at)gdatp.com
This e-mail message (including attachments, if any) is for the sole use of the intended recipient(s) and may contain information that is private, confidential, or exempt from disclosure. Any unauthorized review, use, copying, printing, disclosure, retention, or distribution is strictly prohibited. If you are not the intended recipient, please contact the sender by reply to this e-mail, and delete all copies without disclosing this message to others. Thank you.
[quote]

href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com

[b]

- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
View user's profile Send private message Visit poster's website
MChase(at)gdatp.com
Guest
PostPosted: Tue Mar 13, 2007 7:53 am    Post subject: Tailcone question Reply with quote
John,

Sorry no pictures as I am on the road, but I can give you a dimension. I am looking at 1/16 miss alignment over a 4-6 inch length around the bend location.

Any thoughts?

Michael Chase
General Dynamics Armament and Technical Products
802-657-6029 Office
802-922-5930 Cell
mchase(at)gdatp.com


This e-mail message (including attachments, if any) is for the sole use of the intended recipient(s) and may contain information that is private, confidential, or exempt from disclosure. Any unauthorized review, use, copying, printing, disclosure, retention, or distribution is strictly prohibited. If you are not the intended recipient, please contact the sender by reply to this e-mail, and delete all copies without disclosing this message to others. Thank you.



"John Jessen" <jjessen(at)rcn.com>
Sent by: owner-rv10-list-server(at)matronics.com
03/12/2007 11:00 AM Please respond to
rv10-list(at)matronics.com

To
<rv10-list(at)matronics.com> cc
Subject
RE: Tailcone question




Michael, some pictures would help.

If you looked at my website, and my discussion of the process, I didn't have alignment problems, but only because I snuck up on the final bend. You also have to be a little careful not to put a twist into it, so when you whack it, you really want the pressure you're putting on it to be in the final bend direction. Anyway, send some pictures of what the alignment problem is. And get some heat!

John Jessen
#40328

From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Michael D Chase
Sent: Monday, March 12, 2007 7:33 AM
To: rv10-list(at)matronics.com
Subject: Tailcone question


OK so here I am back with questions about the tail cone and that darn F-1032 Longerion? Anyway I think I am past the point of breaking them, but how about alignment with the skin. I see in the instructions that they want me us to line up the edges, did anyone else have an issue or have to work at this? Looking at a bunch of websites I don't see anyone who even talks about this effort. I am trying to figure out if I messed up my bend or if it is just because it was so cold in my shop when I tried to line everything up. I question more then the bend just because my alignment issues were not just limited to near the bend, but also existing forward of the bend with good alignment the first 1-2 feet then 1 foot off then back on just before the bend ect. This may be just the cold contributing to my issues as it was -28F that AM, I am definitely in the market for a small wood stove before next winter:-)

thanks for the help



Michael Chase
General Dynamics Armament and Technical Products
802-657-6029 Office
802-922-5930 Cell
mchase(at)gdatp.com


This e-mail message (including attachments, if any) is for the sole use of the intended recipient(s) and may contain information that is private, confidential, or exempt from disclosure. Any unauthorized review, use, copying, printing, disclosure, retention, or distribution is strictly prohibited. If you are not the intended recipient, please contact the sender by reply to this e-mail, and delete all copies without disclosing this message to others. Thank you.


href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com




FORUMS -


[quote][b]

- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
n8vim(at)arrl.net
Guest
PostPosted: Tue Mar 13, 2007 8:54 am    Post subject: Tailcone question Reply with quote
Mike,
I'm not the intended recipent.... But not to worry, I haven't told
anyone Smile

But as for deleting the copies... Or retention... My memory isn't
that switchable... Sorry Smile

-Jim
do not archive... Lawyer-based humor involved
Michael D Chase wrote:
Quote:

John,

Sorry no pictures as I am on the road, but I can give you a dimension.
I am looking at 1/16 miss alignment over a 4-6 inch length around the
bend location.

Any thoughts?

Michael Chase
General Dynamics Armament and Technical Products
802-657-6029 Office
802-922-5930 Cell
mchase(at)gdatp.com
This e-mail message (including attachments, if any) is for the sole
use of the intended recipient(s) and may contain information that is
private, confidential, or exempt from disclosure. Any unauthorized
review, use, copying, printing, disclosure, retention, or distribution
is strictly prohibited. If you are not the intended recipient, please
contact the sender by reply to this e-mail, and delete all copies
without disclosing this message to others. Thank you.

*"John Jessen" <jjessen(at)rcn.com>*
Sent by: owner-rv10-list-server(at)matronics.com

03/12/2007 11:00 AM
Please respond to
rv10-list(at)matronics.com

To
<rv10-list(at)matronics.com>
cc

Subject
RE: Tailcone question



Michael, some pictures would help.

If you looked at my website, and my discussion of the process, I
didn't have alignment problems, but only because I snuck up on the
final bend. You also have to be a little careful not to put a twist
into it, so when you whack it, you really want the pressure you're
putting on it to be in the final bend direction. Anyway, send some
pictures of what the alignment problem is. And get some heat!

John Jessen
#40328

------------------------------------------------------------------------
*From:* owner-rv10-list-server(at)matronics.com
[mailto:owner-rv10-list-server(at)matronics.com] *On Behalf Of *Michael D
Chase*
Sent:* Monday, March 12, 2007 7:33 AM*
To:* rv10-list(at)matronics.com*
Subject:* Tailcone question
OK so here I am back with questions about the tail cone and that darn
F-1032 Longerion? Anyway I think I am past the point of breaking
them, but how about alignment with the skin. I see in the
instructions that they want me us to line up the edges, did anyone
else have an issue or have to work at this? Looking at a bunch of
websites I don't see anyone who even talks about this effort. I am
trying to figure out if I messed up my bend or if it is just because
it was so cold in my shop when I tried to line everything up. I
question more then the bend just because my alignment issues were not
just limited to near the bend, but also existing forward of the bend
with good alignment the first 1-2 feet then 1 foot off then back on
just before the bend ect. This may be just the cold contributing to
my issues as it was -28F that AM, I am definitely in the market for a
small wood stove before next winter:-)

thanks for the help

Michael Chase
General Dynamics Armament and Technical Products
802-657-6029 Office
802-922-5930 Cell
mchase(at)gdatp.com
This e-mail message (including attachments, if any) is for the sole
use of the intended recipient(s) and may contain information that is
private, confidential, or exempt from disclosure. Any unauthorized
review, use, copying, printing, disclosure, retention, or distribution
is strictly prohibited. If you are not the intended recipient, please
contact the sender by reply to this e-mail, and delete all copies
without disclosing this message to others. Thank you.
*

href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com

*
*

FORUMS -

*
*
*


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
james.k.hovis(at)gmail.co
Guest
PostPosted: Tue Mar 13, 2007 9:07 am    Post subject: Tailcone question Reply with quote
Be glad I don't attach the ITAR warning on my e-mail to this list.....

Kevin H.
On 3/13/07, James Hein <n8vim(at)arrl.net> wrote:
Quote:


Mike,
I'm not the intended recipent.... But not to worry, I haven't told
anyone Smile

But as for deleting the copies... Or retention... My memory isn't
that switchable... Sorry Smile

-Jim
do not archive... Lawyer-based humor involved
Michael D Chase wrote:
>
> John,
>
> Sorry no pictures as I am on the road, but I can give you a dimension.
> I am looking at 1/16 miss alignment over a 4-6 inch length around the
> bend location.
>
> Any thoughts?
>
> Michael Chase
> General Dynamics Armament and Technical Products
> 802-657-6029 Office
> 802-922-5930 Cell
> mchase(at)gdatp.com
>
>
> This e-mail message (including attachments, if any) is for the sole
> use of the intended recipient(s) and may contain information that is
> private, confidential, or exempt from disclosure. Any unauthorized
> review, use, copying, printing, disclosure, retention, or distribution
> is strictly prohibited. If you are not the intended recipient, please
> contact the sender by reply to this e-mail, and delete all copies
> without disclosing this message to others. Thank you.
>
>
>
> *"John Jessen" <jjessen(at)rcn.com>*
> Sent by: owner-rv10-list-server(at)matronics.com
>
> 03/12/2007 11:00 AM
> Please respond to
> rv10-list(at)matronics.com
>
>
>
> To
> <rv10-list(at)matronics.com>
> cc
>
> Subject
> RE: Tailcone question
>
>
>
>
>
>
>
>
>
> Michael, some pictures would help.
>
> If you looked at my website, and my discussion of the process, I
> didn't have alignment problems, but only because I snuck up on the
> final bend. You also have to be a little careful not to put a twist
> into it, so when you whack it, you really want the pressure you're
> putting on it to be in the final bend direction. Anyway, send some
> pictures of what the alignment problem is. And get some heat!
>
> John Jessen
> #40328
>
> ------------------------------------------------------------------------
> *From:* owner-rv10-list-server(at)matronics.com
> [mailto:owner-rv10-list-server(at)matronics.com] *On Behalf Of *Michael D
> Chase*
> Sent:* Monday, March 12, 2007 7:33 AM*
> To:* rv10-list(at)matronics.com*
> Subject:* Tailcone question
>
>
> OK so here I am back with questions about the tail cone and that darn
> F-1032 Longerion? Anyway I think I am past the point of breaking
> them, but how about alignment with the skin. I see in the
> instructions that they want me us to line up the edges, did anyone
> else have an issue or have to work at this? Looking at a bunch of
> websites I don't see anyone who even talks about this effort. I am
> trying to figure out if I messed up my bend or if it is just because
> it was so cold in my shop when I tried to line everything up. I
> question more then the bend just because my alignment issues were not
> just limited to near the bend, but also existing forward of the bend
> with good alignment the first 1-2 feet then 1 foot off then back on
> just before the bend ect. This may be just the cold contributing to
> my issues as it was -28F that AM, I am definitely in the market for a
> small wood stove before next winter:-)
>
> thanks for the help
>
>
>
> Michael Chase
> General Dynamics Armament and Technical Products
> 802-657-6029 Office
> 802-922-5930 Cell
> mchase(at)gdatp.com
>
>
> This e-mail message (including attachments, if any) is for the sole
> use of the intended recipient(s) and may contain information that is
> private, confidential, or exempt from disclosure. Any unauthorized
> review, use, copying, printing, disclosure, retention, or distribution
> is strictly prohibited. If you are not the intended recipient, please
> contact the sender by reply to this e-mail, and delete all copies
> without disclosing this message to others. Thank you.
> *
>
>
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List
> href="http://forums.matronics.com">http://forums.matronics.com
>
> *
> *
>
> FORUMS -
>
> *
> *
>
>
> *


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV10-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group