 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
jesse(at)saintaviation.co
Guest
|
 Posted: Tue Oct 09, 2007 4:17 pm Post subject: Tail strobe light wires |
 |
|
I would highly recommending using K1000-06 nutplates in place of the pop
rivets on the rudder bottom fairing. You will be glad you did when you have
to get at those wires again. It will also be helpful if you decide to add
rudder trim down the road.
Jesse Saint
Saint Aviation, Inc.
jesse(at)saintaviation.com
www.saintaviation.com
Cell: 352-427-0285
Fax: 815-377-3694
--
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
 |
LarryRosen
Joined: 16 Jan 2006
Posts: 415
Location: Medford, NJ
|
| Posted: Tue Oct 09, 2007 4:44 pm Post subject: Tail strobe light wires |
|
|
I would use 04 nut plates and screws.
Vans Wire harness plans have you making a 3/16 hole through the F-1012
Fuselage Bulkhead stack up. Centered between the lower two bolts.
Larry Rosen
Jesse Saint wrote:
[quote]
I would highly recommending using K1000-06 nutplates in place of the pop
rivets on the rudder bottom fairing. You will be glad you did when you have
to get at those wires again. It will also be helpful if you decide to add
rudder trim down the road.
Jesse Saint
Saint Aviation, Inc.
jesse(at)saintaviation.com
www.saintaviation.com
Cell: 352-427-0285
Fax: 815-377-3694
--
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________
Larry Rosen
#40356
N205EN (reserved)
<http> |
|
| Back to top |
|
|
ddnebert
Joined: 14 Jun 2007
Posts: 17
|
| Posted: Tue Oct 09, 2007 6:50 pm Post subject: Re: Tail strobe light wires |
|
|
Thanks. Larry sent me the pages from section OP37- that must come with the finishing kit. I'm only on the fuselage but am wanting to finish things up more as I go. I carefully installed #6 screw nutplates to hold the strobe/position light to the end of the fairing and will spiral wrap the wires so they can slide all the way in and out in case of repair. Since they go up to a gap in the front of the fairing, I think I can snake 'em if I need to. I'll skip the nutplate suggestion.
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________
RV-10 Builder #40546
Tail mostly done, wings complete, end of SB fuse, working on doors and fiberglass |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
