 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
larry(at)macsmachine.com
Guest
|
 Posted: Sun Jul 27, 2008 3:48 pm Post subject: [Probable Spam] Re: ch601 HDS BUNGEE HELP !!! |
 |
|
Hi Jerry,
The bolts inserted from the outside in is difficult, but you can weld a
socket to an "L" handle that will enable the fixed position while
turning the head from outside.
See tool at the link,
http://www.macsmachine.com/images/TJH/gearAW/full/gear-support-nut-holding-wr.gif
A perhaps better solution suggested the use of a metal strip that had
matching threaded holes that could be found and more easily got to from
the outside.
Pushing the bungees out of the way is also great fun while putting the
nuts in, but I've done this three times and can do it in about
20-minutes now.
Larry McFarland
jeyoung65(at)aol.com wrote:
[quote] Larry, Not sure you have not already covered this BUT I am having one
BIG job trying to install the nuts on the top bolts that goes through
the angles on the wing bottom. Have though about removing the gears
and installing nut plates. Cann't see or feel the bolts. How did you
do it? Thanks Jerry of Ga.
--
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
 |
Jeyoung65(at)aol.com
Guest
|
| Posted: Mon Jul 28, 2008 11:09 am Post subject: [Probable Spam] Re: ch601 HDS BUNGEE HELP !!! |
|
|
Thanks Larry, I will try the welded socket first. Jerry of Ga
In a message dated 7/27/2008 7:49:27 P.M. Eastern Daylight Time, larry(at)macsmachine.com writes:
[quote]--> Zenith-List message posted by: LarryMcFarland <larry(at)macsmachine.com>
Hi Jerry,
The bolts inserted from the outside in is difficult, but you can weld a
socket to an "L" handle that will enable the fixed position while
turning the head from outside.
See tool at the link,
http://www.macsmachine.com/images/TJH/gearAW/full/gear-support-nut-holding-wr.gif
A perhaps better solution suggested the use of a metal strip that had
matching threaded holes that could be found and more easily got to from
the outside.
Pushing the bungees out of the way is also great fun while putting the
nuts in, but I've done this three times and can do it in about
20-minutes now.
Larry McFarland
jeyoung65(at)aol.com wrote:
[quote] Larry, Not sure you have not already covered this BUT I am having one
BIG job trying to install the nuts on the top bolts that goes through
the angles on the wing bottom. Have though about removing the gears
and installing nut plates. Cann't see or feel the bolts. How did you
do it? Thanks Jerry of Ga.
--
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
