 |
Matronics Email Lists Web Forum Interface to the Matronics Email Lists
|
View previous topic :: View next topic |
Author |
Message |
Troy Maynor
Joined: 10 Jan 2006 Posts: 162
|
Posted: Fri Mar 27, 2009 4:50 pm Post subject: Hard Points |
|
|
Hey All,
I need help finding the hardpoints for the harnesses. I put off drilling and when it came time to prime and paint it was overlooked. I have the ones at the tunnel drilled however.
If someone could measure theirs and tell me where the centers are for the ones on the side of the fuselage and the ones in the back of the headrests that would be great. I assume the ones in the headrests are centered port to starboard. And the ones on the side of the fuselage; if someone could measure in relation to, say the bottom edge of the door sill and how much forward of the edge of the wing spar entry. I have a Zircon stud finder that will detect metal but I don't trust it completely to find center because of irregular thickness and curvatures make it a little "dodgy". Please help. I was wanting to bolt these in soon. Thanks in advance. BTW, I have an early Classic if that has any bearing.
Troy Maynor
[quote][b]
| - The Matronics Europa-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
Back to top |
|
 |
DuaneFamly(at)aol.com Guest
|
Posted: Fri Mar 27, 2009 8:10 pm Post subject: Hard Points |
|
|
Troy,
Use this information with a grain of salt as I have the XS model.
On the starboard side I measured 275mm from the window ledge down to the top of the plate. Then 355 down to the bottom of the plate. Then from the back of the seat as seen through the wing spar hole to the near plate edge measured 40mm and 130 mm to the far side of the plate. I measured the plate to be 75mmX 75mm square. These measurements were the same of the port side when measured.
Just for S&G, I used my stud finder and was easily able to find the edges of the top, bottom, and forward side. The only side I had a problem with was the side nearest the wing spar hole because of the buildup of plies for re-enforcement.
Give it a try with your stud finder first, mark the edges, then check with the measurements.
Mike Duane A207A
Redding, California
XS Conventional Gear
Jabiru 3300A
Sensenich R64Z N
Ground Adjustable Prop
Feeling the pinch at the grocery store? Make dinner for $10 or less.
[quote][b]
| - The Matronics Europa-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
Back to top |
|
 |
Troy Maynor
Joined: 10 Jan 2006 Posts: 162
|
Posted: Sat Mar 28, 2009 7:46 am Post subject: Hard Points |
|
|
Thanks Duane,
I found the ones in the fuselage. I am comfortable I found center too.
How about the piece in the back of the headrest? Where is the center for the bolt there?
Troy Maynor
Visit - www.EuropaOwners.org
| - The Matronics Europa-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
Back to top |
|
 |
craigb(at)onthenet.com.au Guest
|
Posted: Sat Mar 28, 2009 1:10 pm Post subject: Hard Points |
|
|
My headrest hard points extend upwards from the seat top 80mm
and measure in 75mm from each side of the head rest to find the
top corner at the 80mm height from the seat top. hope this helps
craig
--
| - The Matronics Europa-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
Back to top |
|
 |
fklein(at)orcasonline.com Guest
|
Posted: Sat Mar 28, 2009 2:59 pm Post subject: Hard Points |
|
|
On Mar 28, 2009, at 8:43 AM, europaman wrote:
Quote: | How about the piece in the back of the headrest? Where is the center
for the bolt there?
|
Troy,
Another way of describing the location of the center of the hardpoint
on the back of the headrest is approx. 40mm up from the deck of the CM
on the centerline of the headrest.
Fred
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
| - The Matronics Europa-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
Back to top |
|
 |
DuaneFamly(at)aol.com Guest
|
Posted: Sat Mar 28, 2009 7:39 pm Post subject: Hard Points |
|
|
Troy,
Looks like others beat me to it. Good luck.
Mike
Feeling the pinch at the grocery store? Make dinner for $10 or less.
[quote][b]
| - The Matronics Europa-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
Back to top |
|
 |
Troy Maynor
Joined: 10 Jan 2006 Posts: 162
|
Posted: Sun Mar 29, 2009 9:54 am Post subject: Hard Points |
|
|
Thanks everyone. I'm thankful for the wealth of help available here.
Troy
Visit - www.EuropaOwners.org
| - The Matronics Europa-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
Back to top |
|
 |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|