 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Thruster87
Joined: 16 Apr 2008
Posts: 193
Location: Australia
|
 Posted: Wed Oct 21, 2009 11:46 am Post subject: Drilling 1/8" hole on the fuel vent tube |
 |
|
How many of you have drilled a 1/8' hole at the back of the fuel vent tubes [just above the angle cutout] to stop siphoning ????? Is it really needed ??? Cheers T87
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
 |
Ron Lendon
Joined: 10 Jan 2006
Posts: 685
Location: Clinton Twp., MI
|
| Posted: Wed Oct 21, 2009 5:17 pm Post subject: Re: Drilling 1/8" hole on the fuel vent tube |
|
|
Is that hole called out in the prints? I must have missed that.
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
_________________
Ron Lendon
WW Corvair with Roy's Garage 5th bearing
CH 601 XLB
N601LT - Flying
http://www.mykitlog.com/rlendon
Corvair Engine Prints:
https://sites.google.com/site/corvairenginedata/ |
|
| Back to top |
|
|
Thruster87
Joined: 16 Apr 2008
Posts: 193
Location: Australia
|
| Posted: Wed Oct 21, 2009 5:35 pm Post subject: Re: Drilling 1/8" hole on the fuel vent tube |
|
|
| Ron Lendon wrote: | | Is that hole called out in the prints? I must have missed that. |
It was in the final check list [about 20 odd pages] for a new 601xl. Can't remember where I down loaded it.Cheers Alan
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
Thruster87
Joined: 16 Apr 2008
Posts: 193
Location: Australia
|
| Posted: Wed Oct 21, 2009 9:30 pm Post subject: Re: Drilling 1/8" hole on the fuel vent tube |
|
|
It was in this document
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
| Description: |
|
Download |
| Filename: |
CH 601 XL SLSA PRE-FLIGHT INSPECTION 2008.pdf |
| Filesize: |
150.68 KB |
| Downloaded: |
943 Time(s) |
|
|
| Back to top |
|
|
Ron Lendon
Joined: 10 Jan 2006
Posts: 685
Location: Clinton Twp., MI
|
| Posted: Fri Oct 23, 2009 3:45 am Post subject: Re: Drilling 1/8" hole on the fuel vent tube |
|
|
| Thruster87 wrote: | | How many of you have drilled a 1/8' hole at the back of the fuel vent tubes [just above the angle cutout] to stop siphoning ????? Is it really needed ??? Cheers T87 |
I don't see what you are referencing in the SAMPLE book you posted. To the best of my knowledge the vent gets cut on a 45 degree angle which faces forward. This is done to create a positive pressure inside the tank during flight.
Could you point it out for me? Or give me a search term to find what you are referring to?
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
_________________
Ron Lendon
WW Corvair with Roy's Garage 5th bearing
CH 601 XLB
N601LT - Flying
http://www.mykitlog.com/rlendon
Corvair Engine Prints:
https://sites.google.com/site/corvairenginedata/ |
|
| Back to top |
|
|
Thruster87
Joined: 16 Apr 2008
Posts: 193
Location: Australia
|
| Posted: Fri Oct 23, 2009 11:58 am Post subject: Re: Drilling 1/8" hole on the fuel vent tube |
|
|
Posted the wrong pdf file Try this one,I've been flat out getting the final inspection done and starting the high speed taxi runs Cheers Alan
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
| Description: |
|
Download |
| Filename: |
Zodiac_CH601_650_inspection_%20checklist.pdf |
| Filesize: |
1.64 MB |
| Downloaded: |
4285 Time(s) |
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
