 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
armywrights(at)adelphia.n
Guest
|
 Posted: Sun Apr 09, 2006 5:53 am Post subject: fuse stand |
 |
|
I’ve got Rick’s fuse stand pics, but wondering if Van’s has a recommended way to make the pallet stand that folks talk about. Sounds like a couple of pallets screwed together with casters on the bottom will work…?
Rob #392
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
 |
jim(at)CombsFive.Com
Guest
|
| Posted: Sun Apr 09, 2006 7:32 am Post subject: fuse stand |
|
|
I bolted on a set of tires using 2" aluminum angle. It allowed me to roll the fuselage in and out of the garage. It turned to to be about a good height for me to reach over the top longerons to work.
Made fiting the fiberglass cabin top easy too.
Jim Combs
N312F
#40192 - Fuselage
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
| Description: |
|
| Filesize: |
118.66 KB |
| Viewed: |
263 Time(s) |
|
|
|
| Back to top |
|
|
Rick S.
Joined: 12 Feb 2006
Posts: 347
Location: Las Vegas
|
| Posted: Sun Apr 09, 2006 1:18 pm Post subject: fuse stand |
|
|
The pallet route was to "Ghetto" for me plus the fact pallets are in big demand in Vegas, the unfourtunate gather them and get $5.00 each for them and I didn't have the heart to steal any let alone toss'em in the back of my expedition.. I didn't like the splinter factor either. So far the stand has worked well, All the riveting has been done and I'm getting ready to get into the fuel lines and controls. FWIW, pallets are usually made out of Oak, perhaps one could fashion their skin bending block from one of the stringers 
I highly recommend getting bigger wheels than I used, I have one wheel that loves to seek out the crack in the floor but on the other hand it has been handy as a chock...so, maybe it's OK.
Jim's system has a lot of potential as well, I would think you could get some 2" angle with the holes predrilled, some 1/4-20 carriage bolts and wing nuts and make his stand easily adjustable in height, a tail wheel should be easy to fabricate with the same material with a wood block attached to the aft tailcone bulkhead.
Rick S.
40185
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
| Description: |
|
| Filesize: |
360.7 KB |
| Viewed: |
238 Time(s) |
|
| Description: |
|
| Filesize: |
364.1 KB |
| Viewed: |
249 Time(s) |
|
_________________
Rick S.
RV-10
40185 |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
