 |
Matronics Email Lists Web Forum Interface to the Matronics Email Lists
|
View previous topic :: View next topic |
Author |
Message |
Arksey(at)aol.com Guest
|
Posted: Fri Dec 09, 2011 8:27 pm Post subject: aileron hinge wire |
|
|
Hi all,
It has turned winter up here in Michigan and the other day I decided to take the firestar out of the hangar and fold it up and store it in the pole barn for the winter...when I laid the tip of the left wing on the ground I noticed the outboard aileron hinge seemed to move alot...when I looked at it to my surprise the wire was gone from the hinge.....this made me nervous even thou I was standing on the ground...when constructed each end of the hinge had been compressed to hold the hinge wire in place....I always do a preflight inspection but may have missed it....the last time I flew I did not notice any problem.....the wire may have come out it the air ...or after I landed when taxing back to the hangar....who knows...just thought I would pass this info on to show you how important preflight inspection is...or can be....jswan
Jim Swan Kolb Firestar ll, 503 Rotax , 6147 Wilcox Rd., Eaton Rapids, Mi 48827 ph 517-663-8488 GPS GPS FOR MY RUNWAY N 42 deg 28.581 W084deg 44.825
[quote][b]
| - The Matronics Kolb-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kolb-List |
|
|
|
Back to top |
|
 |
williamtsullivan(at)att.n Guest
|
Posted: Fri Dec 09, 2011 8:34 pm Post subject: aileron hinge wire |
|
|
Jim- Whoever built my old Firestar drilled and safety wired both ends of the hinges. I don't know which way is recommended. Lucky catch!
Bill Sullivan
Windsor locks, Ct
| - The Matronics Kolb-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kolb-List |
|
|
|
Back to top |
|
 |
donaho1(at)verizon.net Guest
|
Posted: Sat Dec 10, 2011 3:38 am Post subject: aileron hinge wire |
|
|
When I constructed my Firestar II. I cut the hinge wire 1/2 inch
shorter then the hinge, then pinched each end of the hinge closed
with a pair of pliers. I`m sure that information was in the
blueprints. That wire isn`t going anywhere, except where it belongs.
Lanny N598LF
| - The Matronics Kolb-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kolb-List |
|
|
|
Back to top |
|
 |
clydemacquarrie(at)eastli Guest
|
Posted: Sat Dec 10, 2011 4:10 am Post subject: aileron hinge wire |
|
|
I installed cotter pins in my hinges which makes it easy to remove the wire
later on if needed.
Clyde MacQuarrie, Mark 111, 582
--------------------------------------------------
From: "Lanny Fetterman" <donaho1(at)verizon.net>
Sent: Saturday, December 10, 2011 7:36 AM
To: <kolb-list(at)matronics.com>
Subject: aileron hinge wire
Quote: |
When I constructed my Firestar II. I cut the hinge wire 1/2 inch shorter
then the hinge, then pinched each end of the hinge closed with a pair of
pliers. I`m sure that information was in the blueprints. That wire isn`t
going anywhere, except where it belongs. Lanny N598LF
|
| - The Matronics Kolb-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kolb-List |
|
|
|
Back to top |
|
 |
Dana

Joined: 13 Dec 2007 Posts: 1047 Location: Connecticut, USA
|
Posted: Sat Dec 10, 2011 4:55 am Post subject: aileron hinge wire |
|
|
At 06:36 AM 12/10/2011, Lanny Fetterman wrote:
Quote: | --> Kolb-List message posted by: Lanny Fetterman <donaho1(at)verizon.net>
When I constructed my Firestar II. I cut the hinge wire 1/2 inch shorter then the hinge, then pinched each end of the hinge closed with a pair of pliers. I`m sure that information was in the blueprints. That wire isn`t going anywhere, except where it belongs. Lanny N598LF |
On my Ultrastar, the wire is longer than the hinges, and simply bent a bit on each end so it can't move.
-Dana
--
Blow your mind, smoke gunpowder.
[quote][b]
| - The Matronics Kolb-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kolb-List |
|
|
|
Back to top |
|
 |
donaho1(at)verizon.net Guest
|
Posted: Sat Dec 10, 2011 5:28 am Post subject: aileron hinge wire |
|
|
At 07:42 AM 12/10/2011, you wrote:
Quote: | At 06:36 AM 12/10/2011, Lanny Fetterman wrote:
>
>
>Dana, That sounds like it may cause alot of extra aerodaminic drag!
> Lanny FSII Do not archive
On my Ultrastar, the wire is longer than the hinges, and simply bent
a bit on each end so it can't move.
-Dana
--
Blow your mind, smoke gunpowder.
<http://www.buildersbooks.com>www.buildersbooks.com
<http://www.matronics.com/contribution>http://www.matronics.com/contribution
<http://www.matronics.com/Navigator?Kolb-List>http://www.matronics.com/Navigator?Kolb-List
<http://www.matronics.com/contribution>http://www.matronics.com/contribution
|
| - The Matronics Kolb-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kolb-List |
|
|
|
Back to top |
|
 |
donaho1(at)verizon.net Guest
|
Posted: Sat Dec 10, 2011 5:53 am Post subject: aileron hinge wire |
|
|
On my Ultrastar, the wire is longer than the hinges, and simply bent
a bit on each end so it can't move.
Quote: | >Dana, That sounds like it may cause alot of extra aerodaminic drag!
> Lanny FSII Do not archive
|
| - The Matronics Kolb-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kolb-List |
|
|
|
Back to top |
|
 |
HShack(at)aol.com Guest
|
Posted: Sat Dec 10, 2011 6:14 pm Post subject: aileron hinge wire |
|
|
Some years back, I discovered a hinge pin missing from the aileron on my FS II, For some reason, the aileron would not move. It was the inner one.
When I replaced the pin, I just cut it about 3/4" long and bent the ends 90*. That makes it easy to see if the pin is in at preflight.
Shack
In a message dated 12/10/2011 6:38:48 A.M. Eastern Standard Time, donaho1(at)verizon.net writes:
Quote: | When I constructed my Firestar II. I cut the hinge wire 1/2 inch
|
[quote][b]
| - The Matronics Kolb-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kolb-List |
|
|
|
Back to top |
|
 |
neilsenrm(at)gmail.com Guest
|
Posted: Sun Dec 11, 2011 8:44 am Post subject: aileron hinge wire |
|
|
When I built my MKIIIC I drilled the ends of all hinges so that I could install safety wires to hold the hinge pins in place. I figured that someday I might want to remove the hinge pins, the safety wires are easily removable, and are secure although I inspect them regularly.
Rick Neilsen
Redrive VW Powered MKIIIC
On Sat, Dec 10, 2011 at 9:11 PM, <HShack(at)aol.com (HShack(at)aol.com)> wrote:
[quote] Some years back, I discovered a hinge pin missing from the aileron on my FS II, For some reason, the aileron would not move. It was the inner one.
When I replaced the pin, I just cut it about 3/4" long and bent the ends 90*. That makes it easy to see if the pin is in at preflight.
Shack
In a message dated 12/10/2011 6:38:48 A.M. Eastern Standard Time, donaho1(at)verizon.net (donaho1(at)verizon.net) writes:
Quote: | When I constructed my Firestar II. I cut the hinge wire 1/2 inch
|
Quote: |
_blank">www.aeroelectric.com
.com" target="_blank">www.buildersbooks.com
="_blank">www.homebuilthelp.com
_blank">http://www.matronics.com/contribution
get="_blank">http://www.matronics.com/Navigator?Kolb-List
tp://forums.matronics.com
_blank">http://www.matronics.com/contribution
|
[b]
| - The Matronics Kolb-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kolb-List |
|
|
|
Back to top |
|
 |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|