 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
VE3LVO(at)rac.ca
Guest
|
 Posted: Wed Jul 19, 2006 9:24 am Post subject: top of cooling duct 914 |
 |
|
Cheers,
I am looking at a square cutting on three sides with the usual
crack control drill hole at each end. This +/-2inch cutting carries no
infromation in the manual that I can find - but perhaps I've missed the
reference.
It would appear to permit access to the turbo control area
further back OR provide cooling air to a certain facility.
If you know of its purpose, or have divined same from superior
research - and are able to take a moment to explain - I would appreciate the
knowledge, as am about to finalise the fitting of the engine and its
accessories.
Much obliged in advance,
Ferg Kyle
Europa A064 914 Classic
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
 |
jodel(at)nildram.co.uk
Guest
|
| Posted: Wed Jul 19, 2006 11:26 am Post subject: top of cooling duct 914 |
|
|
Ferg,
If you are refering to the bendable flap about 6" down the cooling duct and
on the lefthand side (looking rearwards), It should be bent down into the
airflow to direct air up and around the turbocharger.
The pictures on page 4-4 of the 914 manual(
http://www.europa-aircraft.biz/pdfs/xs914%20may%2006.vp.pdf ) actually show
a 912s hence the lack of the flap. If you look VERY carefully at the
pictures on 4-6 & 4-7 you can just see the flap.
Cheers
Simon
--
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
josok-e(at)ukolo.fi
Guest
|
| Posted: Wed Jul 19, 2006 12:10 pm Post subject: top of cooling duct 914 |
|
|
There is a drawing ofit on page 4-1 issue 4 of the cutting, it reads "914
only" Probably for turbo cooling.
Kind Regards,
Jos Okhuijsen
workshopcam http://www.okhuijsen.org/plane
http:www.europaowners.org/kit600
mono xs, top on, gear in, tail wheel in, wings set, flapdrive in, tail
closed, tailwheel in, tail top in, blue stuff filled, sanded and primed,
fuel system in, doors done, windows in, sanding and filling the fuse and
wings.
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
BEBERRY(at)AOL.COM
Guest
|
| Posted: Wed Jul 19, 2006 12:42 pm Post subject: top of cooling duct 914 |
|
|
Ferg,
On my 914 the only hole in the turbo box cover is to provide for a 2" cooling pipe for the voltage control unit. This is not square.
Patrick
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
