Matronics Email Lists :: View topic - B&C voltage regulator low voltage warning

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

B&C voltage regulator low voltage warning

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

nuckollsr(at)cox.net
Guest

Posted: Sun Jun 24, 2007 7:19 pm Post subject: B&C voltage regulator low voltage warning

At 06:03 AM 6/24/2007 -0700, you wrote:



 	  Quote: 	
		  



I have a B&C voltage regulator that controls one of their 60-amp,

12volt alternators.  One characteristic of this regulator that has

been there since day one is that immediately upon starting the engine

I get a steady low-voltage light (LED), even though the measured

output voltage is normal.  By the time I do a runup and take off the

light goes off.  It is a steady light, not the flashing light that

would indicate an actual low voltage condition.  I went to a lower

bypass resistor,


	


   ??? bypass resistor? Don't know what that is. Oh, you're using

   a LED. Try hooking a incandescent lamp up temporarily and see

   if that works. The circuit was not originally designed to work

   with LEDs. What LED resistor values are you using?

 	  Quote: 	
		    but it is still there.  Anyone else have the

problem?  For now I just ignore it.


	


   What does it do when the engine is running and the

   alternator is shut off? Does it come back on steady

   or does it flash? I think your resistor values

   need to be reviewed.



   Bob . . .

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

Deems Davis

Joined: 09 Jan 2006
Posts: 925

Posted: Sun Jun 24, 2007 8:07 pm Post subject: B&C voltage regulator low voltage warning

I would like to subsitute an LED for the Low Voltage bulb that came with 

the B&C LR3C-14 . I posed the question to Tim Hedding (at) B&C and received 

this in response.



If you use an LED instead of an incandescent lamp, install a 470 - 510 Ohm,

1/2 Watt, resistor between terminals 3 and 5 of the LR3C-14 (or the SB1B-14)

so that the LED does not glow dimly all of the time.



Deems Davis # 406

Engine / Wiring and Panel Stuff

http://deemsrv10.com/



 	  Quote:

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

EricWalker
Guest

Posted: Mon Dec 23, 2019 12:37 am Post subject: Re: B&C voltage regulator low voltage warning

Mechanism of the ruling is deposed for the intelligent individuals. The change of the ‌‌british assignment writers is brought for the forms for all kids. The role is assigned for the mixing of the laws. Path is  issued for the management of the terms. The procedure is allowed for the fitness of the bloggers for the town and its impact for the sizable rules.

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

johnbright

Joined: 14 Dec 2011
Posts: 166
Location: Newport News, VA

Posted: Mon Dec 23, 2019 7:34 pm Post subject: Re: B&C voltage regulator low voltage warning

Hi Deems... ref: http://aeroelectric.com/Pictures/Schematics/LR3_LV_Led_1.jpg



 	  Deems Davis wrote: 	
		  I would like to subsitute an LED for the Low Voltage bulb that came with 

the B&C LR3C-14 . I posed the question to Tim Hedding (at) B&C and received 

this in response.



If you use an LED instead of an incandescent lamp, install a 470 - 510 Ohm,

1/2 Watt, resistor between terminals 3 and 5 of the LR3C-14 (or the SB1B-14)

so that the LED does not glow dimly all of the time.



Deems Davis # 406

Engine / Wiring and Panel Stuff

http://deemsrv10.com/



 	  Quote:

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
John Bright, RV-6A, at FWF, O-360
Z-101 single batt dual alt SDS EM-5-F.
john_s_bright@yahoo.com, Newport News, Va
N1921R links

nuckolls.bob(at)aeroelect
Guest

Posted: Thu Dec 26, 2019 10:12 am Post subject: B&C voltage regulator low voltage warning

At 09:34 PM 12/23/2019, you wrote:

  	  Quote: 	
		  --> AeroElectric-List message posted by: "johnbright" <john_s_bright(at)yahoo.com>



 Hi Deems... ref:  http://aeroelectric.com/Pictures/Schematics/LR3_LV_Led_1.jpg



 

 Deems Davis wrote:

 > I would like to subsitute an LED for the Low Voltage bulb that came with 

 > the B&C LR3C-14 . I posed the question to Tim Hedding (at) B&C and received 

 > this in response.

 > 

 > If you use an LED instead of an incandescent lamp, install a 470 - 510 Ohm,

 > 1/2 Watt, resistor between terminals 3 and 5 of the LR3C-14 (or the SB1B-14)

 > so that the LED does not glow dimly all of the time. 	


   Either of these techniques works . . . in fact,

   Tim's suggestion is probably the most elegant.



 

 

   Bob . . .

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum