 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
mtherr(at)yahoo.com
Guest
|
 Posted: Tue Feb 02, 2010 3:32 am Post subject: MP3 SPA Carb question |
 |
|
Do anyone knows how to setup these carbs (instruction sheet or simply brain power)? When it was rebuilt, the shop told me to adjust the idle and whatever else; I don't remember what they told me.
I also don't know what are the rich and the lean sides on the mixture control. Plus; not being used to fly an engine with mixture... do we pull the knob to get leaner or reacher on the dash board?
----------------------------
Michel Therrien CH601-HD, C-GZGQ
http://mthobby.pcperfect.com/ch601
http://pages.infinit.net/mthobby
__________________________________________________________________
The new Internet Explorer® 8 - Faster, safer, easier. Optimized for Yahoo! Get it Now for Free! at http://downloads.yahoo.com/ca/internetexplorer/
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
 |
jaybannist(at)cs.com
Guest
|
| Posted: Tue Feb 02, 2010 5:11 am Post subject: MP3 SPA Carb question |
|
|
Michel,
Common convention is to pull the control on the panel to lean. I have attached a photo of how I attached the control cable to the leaning lever on the carb. Set it up so that the lever is to the "rich" stop when the control handle is fully seated against the stop at the panel. Pulling the control handle fully out will result in idle cut-off.
The idle is adjusted with a spring-tensioned screw on the throttle arm pivot bracket. See photo. It can only be adjusted through experimentation with the engine running. I set the engine running at the proper idle and marked the throttle control rod with a piece of masking tape at the control ferrule. With the engine stopped, I then adjusted the idle screw so that the throttle control would stop at the tape on the rod.
Let me know if you have questions.
Jay Bannister
| Quote: | --> Zenith-List message posted by: Michel Therrien <mtherr(at)yahoo.com (mtherr(at)yahoo.com)>
Do anyone knows how to setup these carbs (instruction sheet or simply brain
power)? When it was rebuilt, the shop told me to adjust the idle and whatever
else; I don't remember what they told me.
I also don't know what are the rich and the lean sides on the mixture control.
Plus; not being used to fly an engine with mixture... do we pull the knob to get
leaner or reacher on the dash board?
|
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
| Description: |
|
| Filesize: |
113.78 KB |
| Viewed: |
1796 Time(s) |
|
| Description: |
|
| Filesize: |
185.83 KB |
| Viewed: |
1796 Time(s) |
|
|
|
| Back to top |
|
|
jaybannist(at)cs.com
Guest
|
| Posted: Tue Feb 02, 2010 5:11 am Post subject: MP3 SPA Carb question |
|
|
Michel,
Common convention is to pull the mixture control on the panel to lean. I have attached a photo of how I attached the control cable to the mixture lever on the carb. Set it up so that the lever is to the "rich" stop when the control handle is fully seated against the stop at the panel. Pulling the control handle fully out will result in idle cut-off.
The idle is adjusted with a spring-tensioned screw on the throttle arm pivot bracket. See photo. It can only be adjusted through experimentation with the engine running. I set the engine running at the proper idle speed and marked the throttle control rod with a piece of masking tape at the control ferrule. With the engine stopped, I then adjusted the idle screw so that the throttle control would stop at the tape on the rod.
Let me know if you have questions.
Jay Bannister
| Quote: | --> Zenith-List message posted by: Michel Therrien <mtherr(at)yahoo.com (mtherr(at)yahoo.com)>
Do anyone knows how to setup these carbs (instruction sheet or simply brain
power)? When it was rebuilt, the shop told me to adjust the idle and whatever
else; I don't remember what they told me.
I also don't know what are the rich and the lean sides on the mixture control.
Plus; not being used to fly an engine with mixture... do we pull the knob to get
leaner or reacher on the dash board?
|
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
| Description: |
|
| Filesize: |
113.78 KB |
| Viewed: |
1796 Time(s) |
|
| Description: |
|
| Filesize: |
185.83 KB |
| Viewed: |
1796 Time(s) |
|
|
|
| Back to top |
|
|
mtherr(at)yahoo.com
Guest
|
| Posted: Wed Feb 03, 2010 3:55 am Post subject: MP3 SPA Carb question |
|
|
Thanks for the info and pictures!
do not archive
----------------------------
Michel Therrien CH601-HD, C-GZGQ
http://mthobby.pcperfect.com/ch601
http://pages.infinit.net/mthobby
--- On Tue, 2/2/10, jaybannist(at)cs.com <jaybannist(at)cs.com> wrote:
| Quote: | From: jaybannist(at)cs.com <jaybannist(at)cs.com>
Subject: Re: MP3 SPA Carb question
To: zenith-list(at)matronics.com
Received: Tuesday, February 2, 2010, 8:06 AM
Michel,
Common convention is to pull the control on the panel to
lean. I have attached a photo of how I attached the
control cable to the leaning lever on the carb. Set it up so
that the lever is to the "rich" stop when the
control handle is fully seated against the stop at the
panel. Pulling the control handle fully out will
result in idle cut-off.
The idle is adjusted with a spring-tensioned screw on the
throttle arm pivot bracket. See photo. It can
only be adjusted through experimentation with the engine
running. I set the engine running at the proper idle and
marked the throttle control rod with a piece of masking tape
at the control ferrule. With the engine stopped, I
then adjusted the idle screw so that the throttle control
would stop at the tape on the rod.
Let me know if you have questions.
Jay Bannister
--> Zenith-List message
posted by: Michel Therrien <mtherr(at)yahoo.com>
Do anyone knows how to setup these carbs (instruction sheet
or simply brain
power)? When it was rebuilt, the shop told me to adjust
the idle and whatever
else; I don't remember what they told me.
I also don't know what are the rich and the lean sides
on the mixture control.
Plus; not being used to fly an engine with mixture... do we
pull the knob to get
leaner or reacher on the dash board?
|
__________________________________________________________________
Connect with friends from any web browser - no download required. Try the new Yahoo! Canada Messenger for the Web BETA at http://ca.messenger.yahoo.com/webmessengerpromo.php
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
